Wismec rx200 2/3 check battery

Q: Why the device always go back to the VW mode from TC mode automatically?
A: Please make sure that your resistance is lower than , otherwise the Wismec rx200 2/3 check battery device will detect itself and will be allowed be used на сколько вредна электронная сигарета с жидкостью only in VW mode.
You could also try to take out the atomizer and switch to TC mode in room temperature.

  1. vape shop миасс
  2. электронные сигареты 100грн
  3. где можно достать электронные сигареты в уфе

Q: Why the device always show “Device too hot” when I press the fire button?
A: Please let the device cool down for a while.
The higher wattage is, the parilka vape shop екатеринбург bigger current will be, then the higher temperature will be, so it will cause more heat.
And you can try to use TCR mode and set the TCR value according to your coil’s material.

TCR value Автоматические электронные сигареты купить Wismec rx200 2/3 check battery range

Our default setting is SS316, TCR value is 120.
If испаритель для электронных сигарет the value is not correct, the device will detect itself and give a wrong judgment and output.

Q: Why the device always show “imbalanced” ?
A: For the imbalanced message, it means the voltage among your 3 batteries are not imbalance. The difference is higher than .
Please check your электронные сигареты парламент iqos купить batteries again.
We suggest you to change another 3 high-rate batteries with same parameter.

Q: What if the device cannot turn on after charging?
A: Please try as Wismec rx200 2/3 check battery below:
1. take out the batteries
2. Open the software in the computer
3. где можно купить электронную сигарету по дешевке Plug on the USB to connect computer

Q: What if the device always show “Check Battery”/”Low Battery”/”Weak Battery”?
A: We suggest you to change another set of batteries first. It is recommended to use high-rate batteries.
Besides, pls. try to как заряжать электронную сигарету take out the batteries and tighten up the screw in the following picture:
Wismec rx200 2/3 check battery 1Wismec rx200 2/3 check battery 2

Q: How can I upgrade my firmware to the newest version?
A: Please have a try as Wismec rx200 2/3 check battery the following:
To download the newest software from our website, then unzip the file, and then plug можно ли зарядить электронную сигарету the USB cable to install and upgrade.
Attention: Pls. choose the version according to your computer’s system.

  1. ismoka eleaf bcc
  2. новые электронные сигареты без зарядки
  3. уфа электронные сигареты купить

Q: Why the RX200 cannot reach 250W after being updated to the firmware ?
A: In order to ensure the accuracy of output power, the new firmware introduced a mechanism of rogue rda voltage backward calculation. A little change in calculation occurs due to the round-off of decimal part, but it has no influence in usage. And we will Wismec rx200 2/3 check battery keep improving this new mechanism to give users a better experience.

Q: Why the wattage will go down automatically after upgrading to the firmware tsunami 24 rda клон ?
A: Here is the formula for your preference: P=U 2 /R (P: power; U: voltage; R: resistance). The maximum output voltage of RX200 is 9V. According to the formula, if the resistance of the coil you used is a little larger, the output power will not reach 250w.

Q: What if the device cannot turn on after upgrading?
A: Firstly, please take out the cells, pressing the up button and connecting the device through USB cable to the computer. Secondly, you can also change other USB cables or computers for a try.


Меню:


Последние новости: